configure_wisp was setting up wireless.wwan but leaving
radio0.disabled=1, so wifi reload did nothing and the sta
interface never appeared. Explicitly set radio0.disabled=0
before committing the wireless UCI config.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
wifi up does nothing without a wifi-iface section in UCI (common on fresh
flash). Instead, create a temporary managed interface directly on phy0
via nl80211 (iw phy phy0 interface add scan0 type managed), scan on it,
then delete it. No netifd/UCI involvement needed for scanning.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
On a freshly-flashed OpenWrt router, radio0 is disabled by default so
iw dev returns empty. Detect the PHY via /sys/class/ieee80211/, enable
radio0, run `wifi up`, then poll up to 8s for netifd to create the
virtual interface before handing it to iwinfo scan.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
wlan0 doesn't exist on OpenWrt 25.x with mt76 drivers (Cudy TR1200);
interfaces are named phy0-ap0 etc. `iw dev` handles all mac80211
naming styles. The old while-read loop also exited with code 1 when
no match was found, causing run_ok to fail.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
New RPC methods:
- openwrt.scan-wifi: triggers iwinfo scan on the router radio,
returns networks sorted by signal strength
- openwrt.configure-wan: creates UCI wireless.wwan (sta mode) +
network.wwan (DHCP) + adds wwan to firewall WAN zone, then
calls `wifi reload`
get-status now includes a `wan` object with configured/ssid/ip/
internet fields so the UI can show current uplink state.
Frontend WAN panel: scan → pick SSID (signal bars) → enter password
→ apply. Shows "Configure WAN first" hint above TollGate install
button when internet is not available.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
apk errors were being silently dropped (stdout only). Run apk update
first and fail with a clear "router may have no internet" message if
it fails, rather than a cryptic exit-1 from apk add.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
OpenWrt 25.x switched from opkg to apk as the default package manager,
so devices like the Cudy TR1200 on 25.12.4 don't have /usr/bin/opkg.
When opkg is missing but apk is present, install opkg through apk first
so the rest of the provisioning flow can proceed unchanged.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
`channel.exec()` doesn't source the shell profile, so PATH may not
include /usr/bin on some routers. Using /usr/bin/opkg explicitly
avoids exit-127 surprises. Added opkg_check() to give a clear error
("firmware may not support package management") before attempting
opkg_update, rather than a confusing "command not found" exit code.
Also split the BusyBox-hostile `grep -v 'all\|noarch'` into two
separate greps for the arch-detection fallback.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
BusyBox opkg exits 0 even when 'Cannot install' due to insufficient space,
causing the fallback to silently report success. Now captures stderr and
checks for the failure string explicitly.
Adds user-visible error for the common case where the router flash is too
small for the TollGate package (~19 MB needed vs ~9 MB available on typical
budget routers). Adds error prefixes to the RPC sanitizer allowlist so the
message reaches the UI instead of showing 'Check server logs'.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- OpenWrtGateway.vue: add "Install TollGate" button when not installed;
tracks connected credentials for reuse in the provision call
- install.rs: fall back to wget download from GitHub releases when the
package is not in any opkg feed (mips_24kc and other arches supported)
- openwrt.rs: provision-tollgate now falls back to saved router_config
for credentials, matching the behaviour of get-status
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
New `archipelago-openwrt` workspace crate provides SSH/UCI-based management
of OpenWrt routers, including automated TollGate installation and configuration
of a pay-as-you-go "archipelago" SSID backed by the local Cashu mint.
Exposes two RPC endpoints:
- `openwrt.scan` — discover OpenWrt routers on the LAN
- `openwrt.provision-tollgate` — install tollgate-module-basic-go, write UCI
config (TIP-01/TIP-02), and create isolated WiFi SSID + firewall zone
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
